Stuart-turner Monsoon U1.5 bar Twin Manuale Utente

Installation, Operation & Maintenance InstructionsPlease leave this instruction booklet with the home owner as it contains important guarantee, ma

- 10 -Cont ...3.13 Typical Low Level Installation: In certain installations it may be necessary to install a 90° bend on the inlet or outlet co

- 11 -Cont ...4.16 Earthing: This appliance must be earthed via the supply cord, which must be correctly connected to the earth point located in

- 12 - The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is

- 13 -Cont ... To enable correct assembly of the cable gland the ‘O’-ring (Fig. 12 item 1) must be placed over the cable before the clamping ins

- 14 -5 COMMISSIONING5.11 System Flushing: This pump incorporates push-in connectors and plastic components that must not come into contact with

- 15 -Cont ...5.14 Starting: a) Ensure all outlets are closed, turn power supply ‘on’ - pump will start, pressurise the system then stop. b

- 16 -Cont ...6 MAINTENANCE6.11 Turn off water supplies to the pump and release pressure by opening water outlets before attempting maintenance.

- 17 -Cont ...6.14 Pressure vessel: Should ever the need arise for the vessel to have its air charge checked or replenished, it should be carried

- 18 -Stuart Turner reserve the right to amend the specification in line with its policy of continuous development of its products.Note: For informat

- 19 -8 TROUBLE SHOOTING GUIDESymptoms Probable Cause Recommended ActionPump will not start. Electrical supply. Check power supply.Check fuse (see fu

- 2 -PRODUCT DESCRIPTIONElectric motor driven twin ended peripheral pumps complete with an automatic control system, consisting of flow switches, pres

- 20 -Cont ...8.11 Dry Run Protection: This pump is fitted with a PCB that will detect the following fault conditions:  Dry running caused by wat

- 21 -Cont ... IMPORTANT – Ensure there is no contact with any of the internal parts of the terminal box.  Briefly reconnect the mains power su

- 22 -Cont ...8.14 Flow Switch Circuit Test:1. First confirm visually that the flow switch reed clamps have not been dislodged during handling

- 23 -Cont ...9 THE MONSOON GUARANTEECongratulations on purchasing a Stuart Turner pump. We are confident this pump will provide many years of troubl

- 24 -In the event of a claim please telephone ‘Pump Assist’ or return the pump and flexible hoses with the accessories removed e.g pipes etc. If you

- 25 -NOTES

- 26 -NOTES

- 27 -NOTES

Stuart Turner Ltd, Henley-on-Thames, Oxfordshire RG9 2AD ENGLAND Tel: +44 (0) 1491 572655, Fax: +44 (0) 1491 573704email: pumps@stuart-turn

- 3 -Cont ...CHECKLISTItemDescription QtyItemDescription QtyPump 1 Tank & sealing washers 1Hose & sealing washer 4ACBYour product may vary sli

- 4 -Cont ...1 READ BEFORE COMMENCING PUMP INSTALLATIONA. Water storage capacity.1.11 The hot and cold water storage capacity must be sufficient to

- 5 -Cont ...2 LOCATION - GENERAL2.11 Access: For emergencies and maintenance the pump must be easily accessible.2.12 Protection: The pump must

- 6 -2.26 Non-preferred pump location: If it is not possible to locate the pump in the preferred area due to site limitations and it is necessar

- 7 -Cont ...Cold water connection:2.27 The cold water supply: The supply must be air free and have a dedicated connection to the tank which sh

- 8 -Cont ...3 PUMP CONNECTIONS  Do not use stainless steel, chrome or nickel plated pipe with the flexible hose push-in plumbing connections.

- 9 -Cont ...3.12 Hose to pipework:1. The hoses are fitted with plastic push-in connectors, which must only be connected with the following: a